In Vacuum Assisted Resin Transfer Molding (VARTM) and resin infusion processes, selecting the right layup consumables directly impacts laminate quality, labor efficiency, and cycle time. While traditional single-layer materials offer flexibility, pre-combined multi-layer consumables are transforming composite manufacturing by reducing layup time and human error.
Below is a comprehensive breakdown of our three core vacuum infusion solutions—Single-Layer Peel Ply, 2-in-1 Flow Media + Perforated Release Film, and 3-in-1 All-in-One Infusion Combo—to help engineers and procurement teams select the ideal configuration.
Link: https://en.ninezerotech.com/
1. Product Specifications & Structural Breakdown
Option 1: Single-Layer Peel Ply (Traditional Foundation)

Structure: 100% woven fabric (Polyester or Nylon).
Core Role: Placed directly against the composite laminate to create a clean, textured surface ready for secondary bonding or painting without heavy sanding.
Best For: Wet layup, hand layup, prepreg vacuum bagging, and custom infusion layups where each layer needs independent positioning.
Code | Gram(g/m²) | Recommended TEMP ℃ | Width(mm) | Material | Roll Length(m) |
CVP150 | 85 | 150 | 100-2300 | Polyester | 50-500 |
CVP150 | 105 | 150 | 100-2300 | Polyester | 50-500 |
CVP200 | 85 | 200 | 100-2300 | PA6 | 50-500 |
CVP200 | 105 | 200 | 100-2300 | PA6 | 50-500 |
CVP230 | 85 | 230 | 100-2300 | PA66 | 50-500 |
CVP230 | 105 | 230 | 100-2300 | PA66 | 50-500 |
Option 2: 2-Layer Combo (Flow Media + Perforated Release Film)

Outermost Layer (Release Film): 30µm Red Perforated Film (Pore diameter: 0.8mm ±0.1, Pore spacing: 5mm ±0.1), Width: 145cm, Roll Length: 100m.
Innermost Layer (Flow Media): 140gsm Green Woven Infusion Mesh, Width: 143cm, Roll Length: 100m.
Core Role: Combines resin distribution and controlled resin bleed/separation into a single roll, eliminating the need to lay down release film and flow mesh separately. (Note: Requires a separate peel ply underneath if surface texturing is needed).
2 Layers | Flow Media | Peel Ply | Release Film | Width (mm) |
CVMW160 | / | CVR120 | 1450 | |
160g/m², 120℃, Green, Woven | 30μm, 120℃, Red, PE, Perforated | |||
CVME200 | / | CVR150 | 1450 | |
200g/m², 120℃, Green, Extruding | 35μm, 150℃, Red, PE, Perforated | |||
CVME230 | / | CVR230 | 1450 | |
230g/m², 120℃, Green, Extruding | 50μm, 230℃, Blue, PP, Perforated |
Option 3: 3-Layer All-in-One Combo (Flow Media + Release Film + Peel Ply)

Top Layer (Flow Media): 140g/m²~230 g/m² Woven Mesh, Width: 1430mm, Max Temp: 120℃.
Middle Layer (Perforated Release Film): 30µm~50µm Film, Width: 1450mm, Max Temp: 120℃~230℃.
Bottom Layer (Polyester/PA6/PA66 Peel Ply): 85g/m² Fabric, Width: 1500mm, Max Temp: 150℃~230℃.
Core Role: A complete, factory-bonded infusion stack. Notice the stepped width design (1430mm / 1450mm / 1500mm)—this engineered offset prevents resin racing at the edges and ensures the peel ply fully protects the laminate edges during demolding.
3 Layers | Flow Media | Peel Ply | Release Film | Width (mm) |
CVMW100 | CVP150 | CVR120 | 1500 | |
100g/m², 120℃, Green, Weaving | 85g/m², 150℃, Polyester | 30μm, 120℃, Red, PE, Perforated | ||
CVME200 | CVP200 | CVR150 | 1500 | |
200g/m², 120℃, Green, Extruding | 85g/m², 200℃, PA6 | 35μm, 150℃, Red, PE, Perforated | ||
CVME230 | CVP230 | CVR230 | 1500 | |
230g/m², 120℃, Green, Extruding | 85g/m², 230℃, PA66 | 50μm, 230℃, Blue, PP, Perforated |
2. Side-by-Side Comparison Matrix
Feature / Parameter | 1-Layer: Peel Ply | 2-Layer: Flow Media + Release Film | 3-Layer: Flow Media + Release Film + Peel Ply |
Material Layers | Peel Ply only | Flow Media(1430mm)+ Release Film(1450mm) | Flow Media(1430mm) + Release Film(1450mm) + Peel Ply(1500mm) |
Standard Width | Custom(100mm -2300mm) | 1450mm | 1500mm |
Max Operating Temp | Up to 150℃~230℃ | Up to 120℃~230℃ | Up to 120℃~230℃ |
Layup Labor Time | High (3 separate steps if infusing) | Medium (Saves 1 full layup step) | Lowest (Cuts layup time by up to 60%) |
Demolding Efficiency | Strips single layer | Strips flow mesh & film together | Strips all 3 layers in one clean pull |
Key Functional Advantage | Maximum flexibility for complex curves | Fast resin flow + easy mesh release | Zero wrinkle risk, edge-bleed control, fastest cycle time |
3. Application Scenarios: Which One Should You Use?
Choose Single-Layer Peel Ply when:
You are doing hand layup or prepreg curing (no flow media required).
Your mold has extreme 3D contours, deep corners, or sharp radii where multi-layer fabrics might bridge or wrinkle.
You are running high-temperature cures above 120℃
Choose the 2-Layer Combo (Flow Media + Release Film) when:
You already have a preferred specialty peel ply on the part surface, or your part surface does not require peel ply texturing.
You want to speed up medium-to-large flat or gently curved infusion parts (e.g., boat hulls, truck panels) while maintaining 0.8mm precision resin metering.
Choose the 3-Layer Combo (All-in-One) when:
You are producing large-scale, repetitive composite structures where labor cost and mold turnaround time are critical.
Target Industries: Wind turbine blades and nacelles, marine hulls and decks, aerospace secondary structures, automotive body panels, and large FRP tanks/pipes.
You want consistent resin distribution without the risk of layers shifting under vacuum pressure.